Topic 2 - Mechanical Engineering and Engineering Science

HYDRAULIC FLUIDS FOR AUTOMATIC TRANSMISSIONS

Dmytro Mischuk¹, Maxim Balaka², Mykola Hodnevich³

¹Ph.D., assistant professor of Building Machinery, Kyiv National University of Construction and Architecture, Kyiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

²Assistant of Building Machinery, Kyiv National University of Construction and Architecture, Kyiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

³Student of group BMO-22s, Kyiv National University of Construction and Architecture, Kyiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The properties, functions and requirements for the use of hydraulic fluids in automatic transmissions for powerful vehicles and industrial tractors are analyzed in this paper. Their typical characteristics and comparative evaluation of operational properties with transmission oils are given.

Keywords: transmission oil, automatic transmission fluid (ATF).

---

REQUIREMENTS FOR WORKING FLUIDS OF VOLUMETRIC HYDRAULIC DRIVE

Dmytro Mischuk¹, Andriy Boychenko², Maxim Balaka³

¹Ph.D., assistant professor of Building Machinery, Kyiv National University of Construction and Architecture, Kyiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

²Student of group BMO-22s, Kyiv National University of Construction and Architecture,
Kyiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

³Assistant of Building Machinery, Kyiv National University of Construction and Architecture, Kyiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The requirements for the use of hydraulic fluids in volumetric hydraulic drive are considers in paper. A number of properties that influence the quality of working fluids during the operation of automotive and construction machinery are analyzed. Classification and designation of working fluids according to domestic and foreign standards are provided.

 

Keywords: volumetric hydraulic drive, working fluid, property.

---

SYNTHESIS OF HARMONY CONVERTER OF INDUCTIVITY MAGNETITE BASED ON THE COMBINED OPERATING SCHEME

 

Mikola Tverdostup

Ph.D., associate professor of department of electronic calculable machines, Oles Gonchar Dnipro National University, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. Based on the generalized model, the impedance converters are synthesized F-metric converter of inductance of the magnetite sensor to the frequency of harmonic oscillations, for which there is no fundamental limitation of the sensitivity to the variation of the inductance.

Keywords: synthesis, inductive sensor, magnet, impedance converter, operating circuit, feedback, F-meter.

---

UDC 539.3 / 6

ELABORATION OF A METHODOLOGY OF POWER CALCULATIONS OF FLAT FRAMES UNDER CONDITIONS OF FORCED OSCILLATIONS

 

Yu.S. Kholodniak¹, S.V. Kaporovych², Ye.D. Korotenko³

¹ Ph.D., Associate Professor of Technical Mechanics Department, Head of Technical Mechanics Department, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it., This email address is being protected from spambots. You need JavaScript enabled to view it.

² Ph.D., Senior Lecturer of Technical Mechanics Department, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

³ Ph.D., Head of Language Training Department, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

^{1, 2, 3} Donbass State Engineering Academy, Kramatorsk, Ukraine

 

Abstract. The mathematical model proposed in this paper describes oscillations of a weightless frame with a point mass and simultaneous action of vertical and horizontal harmonic disturbing forces. The model is based on the method of forces, which establishes the relationship between the movement of the frame and the forces acting on it. Together with the model, dependences were obtained for calculating resonant frequencies of the oscillating system. The completed developments allow to determine dynamic characteristics of the oscillation process and to calculate frames for strength and rigidity. The methodology for this calculation is implemented in the Mathcad 15 environment and has been successfully tested on a number of learning tasks. The results of the work may be useful to students and teachers of technical universities, as well as practitioners who perform power calculations.

Keywords: plane frame, forced oscillation, mathematical model, resonant frequency, power calculation.

---

PLANNING AND CONDUCTING THE EXPERIMENT FOR THE DETERMINATION OF CARBON CONTENT IN MATERIALS

 

Kirill Ziborov¹, Sergei Fedoriachenko², Ann Moskalenko³

^1,2 Ph.D, Associated Professor of Machinery Design Bases Department, National TU Dnipro Polytechnic, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

³ Student, National TU Dnipro Polytechnic, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The work describes the planning and conduction of an experiment to determine the carbon content of the shaft gear gearbox of a SST-110 turbogenerator (TWIN-AFA 46 GTG) using a coulometric unit of the type AN 7529.1, and the carbon correspondence to ISO GOST 12344-2003 has been determined.

Keywords: carbon, coulometric, doped and high-aluminum steel.

---

EXPERIMENTAL STUDY OF STEEL MICROSTRUCTURE

 

Kirill Ziborov¹, Sergei Fedoriachenko², Mike Remeslo³

^1,2 Ph.D, Associated Professor of Machinery Design Bases Department, National TU Dnipro Polytechnic, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

³ Student, National TU Dnipro Polytechnic, Dnipro, Ukraine

 

Abstract. This article present the data of the material microstructure (shaft of the shaft gear-gear gearbox of the turbogenerator type SST-110) and an experiment using the metallographic microscope NEOPHOT-21.

Keywords: microstructure, steel, experiment, research.

Topic 3 - Transport Technologies and Equipment

---

EUROPEAN APPROACH TO THE PREPARATION OF SPECIALISTS IN THE FIELD OF LOGISTICS AND TRANSPORT ON THE EXAMPLE OF DANISH TECHNICAL UNIVERSITY

 

Oleksiy Goryayinov

Ph.D., Associate Professor of the Transport Technologies and Logistics Department, Kharkiv Petro Vasylenko National Technical University of Agriculture, Kharkiv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The analysis of the master program of the Danish Technical University is made. Program Name: " Master of Science in Engineering (Transport and Logistics)". The differences from the specialty in Ukraine "Transport Technologies" are identified.

Keywords: master program, Denmark, university, transport, logistics.

---

MATHEMATICAL MODEL OF THE REAR SUSPENSION HYBRIDIZED VEHICLE

 

Vladimir Protsiv¹, Tatiana Bas², Аleksandr Chernysh³

¹Ph.D., Professor of the Department of Technology of Mining Engineering, National Technical University ‘Dnipro Polytechnic’, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

²Postgraduate student of the Department of Technology of Mining Engineering, National Technical University ‘Dnipro Polytechnic’, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

³lecturer, Dniprovsky Transport and Economical College, Dnipro, Ukraine

 

Abstract. The mathematical model of the rear suspension of a hybridized vehicle which allows you to calculate the dynamic properties of the suspension and select the necessary units for its modernization is proposed.

Keywords: suspension, hybridized car, mathematical model.

---

DETERMINATION OF PARAMETERS OF AUTOMOBILE ROADS FOR THE SPATIAL MOVEMENT OF UNCLEAR VEHICLES

 

Konstantin Bas¹, Tatiana Bas², Vladimir Shvaika³

¹Ph.D., Professor of the Department of Automobiles and Automobile Economy, National Technical University ‘Dnipro Polytechnic’, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

²Postgraduate student of the Department of Technology of Mining Engineering, National Technical University ‘Dnipro Polytechnic’, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

³ Postgraduate student of the Department of Automobiles and Automobile Economy, National Technical University "Dnipro Polytechnic", Dnipro, Ukraine, e-mail: e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The trajectory of the movement of unmanned vehicles and their performance are determined by technological processes. The question of finding the curvature and torsion of a road that allows one to realize a given trajectory is considered.

Keywords: orts of a natural trihedr, curvature, torsion, program line, hodograph.

Topic 4 - Resource and Energy Saving Technologies and Materials

---

THE SOLUTION OF THE PROBLEM OF GAS DISPOSAL OF MOLDING IN THE FELLOW SPACE OF EXTRACTING WELLS OPERATING SRP

Klara Gabdrakhmanova¹, Gylnara Izmaylova², Sobirdzhan Marupov^3
1 Ph.D., Professor Department ITMEN, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
² Ph.D., Senior Lecturer, Department RRGNM, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
³Student BGR-16-12 group, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.
^1,2,3Ufa State Petroleum Technological University, Branch of the University in the City of Oktyabrsky, 54a, Devonskaya St., Oktyabrsky, Republic of Bashkortostan, 452607, Russian Federation

Abstract. This article presents new approaches to solving one of the problems encountered in many oil fields, which are a problem of utilization of gas accumulating in the annulus of production wells operated by sucker-rod deep well pumps. The focus is on the technical and economic efficiency of the proposed method of associated gas utilization.

Keywords: annular gas, annular pressure, use of associated petroleum, ecology.

---

EQUIPMENT FOR CONDUCTIVE METHOD OF DRYING MATERIALS

 

V.A. Fedoskin¹, N.N. Yerisov², K.I. Kornilenko³

¹Ph.D., Associate Professor of the Department of Automobiles and Automobile Economy, Dnipro University of Technology, Ukraine, е-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

²Assistant of the Department of Automobiles and Automobile Economy, Dnipro University of Technology, Ukraine, е-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

³ Postgraduate student of the Department of Automobiles and Automobile Economy, Dnipro University of Technology, Ukraine, е-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Annotation. The paper considers the installation of a conductive material drying method in which the basic requirements of layer formation and its interaction with a heated surface are realized, uniform distribution of the material across the box width throughout the transportation path is ensured, the transportation path and intensive mixing of the material is increased. The result of this is a significant increase in the drying efficiency of the material and a reduction in coolant flow.

Keywords: vibrotransporter, material drying, layer.

---

THE USING OF POLYMER WASTE IN ROAD COVERINGS

 

Yuriy Khlibyshyn¹, Iryna Pochapska²

¹Ph.D., Associate professor, Department of Organic Products Technology, Lviv Polytechnic National University, Lviv, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

²Ph.D., Associate professor, Department of Civil Safety, Lviv Polytechnic National University, Lviv, Ukraine, e-mail: iryna.y.pochapskaThis email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The means by improving the quality of road bitumen are described. The process modification of bitumen by industrial polymers is investigated. The possibility of modifying bitumen with rubber crumb and the optimal amount of rubber crumb in this process is determined.

Keywords: polymer waste, crumb rubber, bitumen.

Topic 5 - Automation and Mechanization Energy Supply

---

THE PROCEDURE OF SINE-WAVE FILTER PARAMETERS SELECTION IN CASE OF INCREASED FREQUENCY OF VOLTAGE

 

Mikhail Pustovetov

Ph.D., doctoral student of the «Electric trains and locomotives» department of Federal State Institution of Higher Education «Russian University of Transport», Moscow, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The paper proposes and gradually considers the procedure for selecting the parameters of the sine-wave filter for the case of increased (400 ... 1000 Hz) voltage frequency. Limitations and specific requirements affecting the choice of sine-wave filter components discussed.

Keywords: frequency converter, sine-wave filter, simulation.

---

RESEARCH OF THE IMPACT OF VIBRATION ON TECHNICAL CHARACTERISTICS OF MEASURING CONVERTERS

 

Alexey Mikhaylov

Leading Specialist PLC SYSTEM Ltd, Moscow, RF, This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. Vibration testing is an obligatory stage in the development and modernization of any instrument making instrument, including measuring transducers (sensors) of various physical parameters: pressure, temperature, linear and angular accelerations and so on. The main parameters set by vibration tests are frequency, amplitude and time, as well as the law of frequency and amplitude changes. The output parameters are taken informative signals recorded by external electrical devices, as well as quality indicators of the mechanical strength of the transducer.

Keywords: transducer, measurement, vibration, frequency, amplitude, shaker.

---

MODELING OF THE METROLOGICAL CHARACTERISTICS OF THE SENSITIVE ELEMENTS OF CAPACITIVE PRESSURE SENSORS

 

A.V. Sokolov

Inspector RSCS, Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

Abstract. Sensitive elements (CE) and measuring modules (MI) in the sensors of physical quantities are the main structural and functional units that determine most of the metrological characteristics of the sensors: measurement accuracy, metrological reliability and information content. In this regard, CHE and IM are subjected to modeling, calculation and testing at all stages of the development of the measuring channel. In the article the questions of modeling Jae quasidifferentiable type used in a capacitive pressure sensor (EDD).

Keywords: capacity, sensor, model, sensor, quasidifferential.

---

METHODS FOR THE CONVERSION OF THE POWER PARAMETERS IN MULTIFUNCTION SENSORS

 

Z.A. Bayasilova

post-graduate student, Kazakh National Research Technical University K.I. Satpayev, Almaty, Kazakhstan, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. Most multi-function sensors usually measure two parameters - a mechanical value (deformation, pressure and force) and temperature. The measured non-electric values - pressure and temperature have different dynamics and magnitude and dimension. Therefore it is necessary to choose such principles of transformation that they were compatible physically, information, energetically and constructively. Various principles of transformation of non - electric quantities-force and pressure into electric quantity-current, voltage, resistance, frequency are considered and analyzed. Mathematical models describing the transformation functions are presented, the conditions of their adequacy are analyzed.

Keywords model, method, transformation, magnitude, pressure, force, deformation, current, voltage.

 

Topic 7 - Informational Technologies of Design, Modeling, Design, Modern WEB-technologies

---

AUTODESK MODERN TOOLS IN THE MACHINE PARTS DESIGN

 

Sergey Balashov¹, Dmitro Nikituk², Alina Gorohova³

¹Ph.D., Machinery Design Bases Department, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

^2,3Student

^1,2,3 National Technical University ‘Dnipro Polytechnic’, Dnipro, Ukraine

 

Abstract. The paper considers the overview of using possibilities the most common in the world CAD systems on the example of constructing a complex surface of the Wind rotor. The considered problem is tested as an exercise in the engineering drawings subject during the training of junior students.

Keywords: CAD, Autodesk, AutoCad, education, design.

---

MORPHOLOGICAL TRANSFORMATION AS A MEANS OF DESIGN

 

Anastasiia Loginova¹, Ilya Verner², Juliy Stepashko³

¹Ph.D, Associated Professor of Machinery Design Bases Department, National TU Dnipro Polytechnic, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

^2,3Assistant of Machinery Design Bases Department, National TU Dnipro Polytechnic, Dnipro, Ukraine,
²e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it., ³e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The paper presents the basic principles and examples that determine the prospects for the development of the creative use of the principle of morphological transformation in the practice of shaping and in solving problems of modern design. The advantages of the method of morphological transformation, as a means of functional transformation and the provision of functional polysemy of a thing or subject environment are shown.

Keywords: morphologic transform, design arts, shape creations.

---

ECONOMIC EFFICIENCY OF ARTISTIC DESIGN OF TECHNOLOGICAL EQUIPMENT

 

Anastasiia Loginova¹, Ann Moskalenko², Andrey Shelkunov³

¹Ph.D, Associated Professor of Machinery Design Bases Department, National TU Dnipro Polytechnic, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

^2,3student of group 132-16-1, National TU Dnipro Polytechnic, Dnipro, Ukraine.

 

Abstract. The article considers the exact criteria for assessing the economic efficiency of the design and development of the product, and also shows that the increase of aesthetic and ergonomic indicators of special technological equipment increases its complex quality indicators and positively affects the working conditions of the operator. It is shown that this approach allows designers to understand, which takes place in the economic aspect in the field of design, production and operation of the implementation of methods of artistic design.

Key words: quality, art design development, aesthetics of equipment, ergonomics of equipment, economic efficiency of equipment. 

---

COMPARATIVE ANALYSIS OF DESIGNING MACHINE PARTS IN COMPASS-3D AND INVENTOR SOFTWARE

 

Alexander Tverdohleb¹, Ilya Verner², Alexander Telipko³

^1,2Assistant, Machinery Design Bases Department, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

³Student

^1,2,3 National Technical University ‘Dnipro Polytechnic’, Dnipro, Ukraine

 

Abstract. The paper considers the possibilities of using the most common CAD systems such as Inventor and Compass-3D on the example of the reducer elements designing. A comparative analysis of the capabilities of the systems are provided.

 

Keywords: Compas-3D, Autodesk, Inventor, education, design.

---

ASSESSMENT OF STABILITY OF A BULK SOIL DAM OF THE SELIAKKA-YARVI RESERVOIR BY RESULTS OF 3D MODELING

 

Nadezhda Kalashnik

Research Associate of Geoflyuidomechanikal Laboratory, Mining institute KNC RAS, Apatity, Russia,e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. Assessment of stability of a bulk soil dam of the Seliakka-Yarvi reservoir which is the main and important source of production water supply of is executed for sity Zapolyarnyi and industrial facilities of JSC Kola MMC. Researches are executed on the basis of computer 3D modeling and natural hydrogeological and visual definitions. Values and the sizes of zones of full shifts of soil of a dam and the spreading geological basis are revealed. Values of coefficient of stability (safety) of a dam are defined on the basis of what the conclusion is drawn on its state for the considered conditions.

Keywords: reservoir, dam, modeling, movements of soil, stability.

---

THE ANALYSIS AND MATHEMATICAL MODELLING OF EFFECTIVELY CONDUCTOR LAYER IN MAGNETOSTRICTIVE CONVERTERS OF MOVEMENTS

 

Yuri Slesarev¹, Alexander Vorontsov²

¹Dr., Ph.D., professor of Automation and Management department, federal state-funded educational institution of the higher education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

²Ph.D., associate professor "Computers and systems", federal state-funded educational institution of the highest education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. In work it is in detail considered the phenomenon which received the name the skin or a skin effect which is shown in course of alternating electric current in the wave guide surface layer called by also effectively carrying out Ze-layer. The analysis of the pacing factors influencing thickness of a surface layer is made. Mathematical modeling of a skin effect and assessment of thickness of a Ze-layer at different frequency rates of fluctuations of alternating electric current is carried out.

Keywords: skin effect, magnetostrictive converter, effectively conductor layer, superficial effect, modeling of skin-effect.

---

ANALYSIS OF DISTRIBUTION AND MODELLING OF MAGNETIC FIELDS OF MAGNETOSTRICTIVE CONVERTERS OF MOVEMENT

 

Yuri Slesarev¹

¹Doctor of technical Sciences, professor of Automation and Management department, federal state-funded educational institution of the higher education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. In this article modeling of magnetic fields of magnetostrictive converters of movement is considered. Mathematical modeling of resultant tension of magnetic field of magnetostrictive converters of movement and its components – created by a current impulse and a permanent magnet is carried out.

Keywords: magnetic field, modeling of magnetic fields, magnetostrictive converter, tension of magnetic field, tension calculation.

---

ARTIFICIAL NEURAL NETWORKS AND GEOINFORMATION SYSTEMS IN AGRICULTURE

 

Valeriya Zvereva¹, Alex Vorontsov²

¹Student of group 17IV1m, Federal State-funded Educational Institution of the Highest Education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

²Ph.D., associate professor "Computers and systems", federal state-funded educational institution of the highest education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. In the last decade, research in the field of remote sensing has been intensified significantly. It is used in various sectors of the national economy, in particular for agriculture and forestry. The main question, which should be solved with the help of such developments: «How to prevent global losses of harvests, that are calculated in hundreds and thousands of hectares?». This article is devoted to this problem.

Keywords: Information technology, artificial neural networks, remote sensing, geoinformation systems (GIS), cartographic data.

---

THE ANALYSIS AND MATHEMATICAL MODELLING OF CONTINUOUS PERMANENT MAGNETS MAGNETIC FIELDS OF MAGNETOSTRICTIVE CONVERTERS OF MOVEMENT

 

Alexander Vorontsov¹

¹Ph.D., associate professor "Computers and systems", federal state-funded educational institution of the highest education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. In work the analysis of the major factors influencing formation of magnetic fields of magnetostrictive converters of movement when using to them a continuous permanent magnet is in detail considered. The analysis of influence of each factor is made. Settlement formulas of tensions of the magnetic fields created by a continuous permanent magnet are investigated.

Keywords: continuous constant magnet, intensity of a magnetic field, a magnetic field of continuous constant magnet, mathematical modelling of magnetic fields.

---

RESEARCHES AND MATHEMATICAL MODELLING OF THE PROJECTION OF TENSION OF MAGNETIC FIELD OF THE INDUCTIVE ELEMENT TO AXIS 0Z

 

Yuri Slesarev¹

¹Dr., Ph.D., professor of Automation and Management department, federal state-funded educational institution of the higher education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. In work the analysis of the key parameters of an inductive element influencing formation of the magnetic fields created at course in the environment of a wave guide of a current impulse is in detail considered. Mathematical modeling of magnetic field of an inductive element at change of the coordinate counted on OZ axis from its center for various values of radiuses and length of an inductive element is carried out.

Keywords: inductive element, tension of magnetic field, magnetic field, dependence of tension on Z coordinate.

---

THEMATICAL MODELLING AND CALCULATION OF THE TILT ANGLE OF THE PLANE OF THE TWO-COORDINATE MAGNETOSTRICTIVE TILTMETER OF RATHER HORIZONTAL PLANE

 

Alexander Vorontsov¹

¹Ph.D., associate professor "Computers and systems", federal state-funded educational institution of the highest education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. In this article the settlement formula of a tilt angle of the plane of a two-coordinate magnetostrictive goniometer through tilt angles in mutually perpendicular planes is received. Coincidence of numerical values of the results received when modeling and an experimental method demonstrates adequacy of a settlement formula.

Keywords: plane tilt angle, calculation of a tilt angle, two-coordinate magnetostrictive goniometer, magnetostrictive tiltmeter.

---

MATHEMATICAL MODELLING OF MAGNETIC FIELDS OF PERMANENT MAGNETS OF THE CYLINDRICAL FORM NEAR THEIR BASES IN MAGNETOSTRICTIVE CONVERTERS OF MOVEMENTS

 

Yuri Slesarev¹

¹Dr., Ph.D., professor of Automation and Management department, federal state-funded educational institution of the higher education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. permanent magnet, tension of magnetic field, magnetic field of a permanent magnet, tension near the basis of a permanent magnet.

Keywords: inductive element, tension of magnetic field, magnetic field, dependence of tension on Z coordinate.

---

TO THE QUESTION OF THE RESEARCH AND MATHEMATICAL MODELLING OF POSSIBLE DISTANCE FROM THE WAVE GUIDE TO THE RING PERMANENT MAGNET

 

Yuri Slesarev¹

¹Dr., Ph.D., professor of Automation and Management department, federal state-funded educational institution of the higher education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. In work modeling in magnetostrictive tiltmeters of possible distances from a ring permanent magnet to the wave guide necessary for sure formation of an ultrasonic wave of torsion is considered. Modeling is carried out by means of the developed program complex "Two-coordinate MN" focused on the analysis of magnetic fields of two-coordinate magnetostrictive tiltmeters. Calculation of optimum distances is performed by the offered technique of determination of permissible values of resultant tension of magnetic field.

Keywords: ring magnet, distance from a permanent magnet to a wave guide, modeling of magnetic fields, tension calculation, optimum distance.

---

TO THE QUESTION OF THE RESEARCH AND MATHEMATICAL MODELLING OF POSSIBLE DISTANCE FROM THE WAVE GUIDE TO THE CONTINUOUS PERMANENT MAGNET

 

Yuri Slesarev¹

¹Dr., Ph.D., professor of Automation and Management department, federal state-funded educational institution of the higher education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. In work modeling in magnetostrictive goniometers of possible distances from a continuous permanent magnet to the wave guide necessary for sure formation of an ultrasonic wave of torsion is considered. Modeling is carried out by means of the developed program complex "Two-coordinate MN" focused on the analysis of magnetic fields of two-coordinate magnetostrictive goniometers. Calculation of optimum distances is performed by the offered technique of determination of permissible values of resultant tension of magnetic field.

Keywords: continuous magnet, distance from a permanent magnet to a wave guide, modeling of magnetic fields, tension calculation, optimum distance.

---

TO THE QUESTION OF APPLICATION OF THE CLOUD COMPUTING IN EDUCATIONAL PROCESS OF HIGHER EDUCATION INSTITUTION ON THE EXAMPLE OF THE PRIVATE CLOUD OF THE PSTU COMPUTER NETWORK

 

Alexander Vorontsov¹

¹Ph.D., associate professor "Computers and systems", federal state-funded educational institution of the highest education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. In this article the analysis of possible prospects of use of a cloud computing in the educational environment on the example of a private cloud of PSTU is made. The questions connected with efficiency of application of the services provided to PSTU to teachers and students when training (the platform and the software, that is PAAS and SAAS) are considered.

Keywords: cloud computing, PSTU, private cloud, prospects of use, educational environment, local networks, global networks.

---

MATHEMATICAL MODELLING OF TEMPORARY CHARACTERISTICS OF COMPUTER NETWORK IN AUDIENCE OF HIGHER EDUCATION INSTITUTION

 

Alexander Vorontsov¹

¹Ph.D., associate professor "Computers and systems", federal state-funded educational institution of the highest education "Penza state technological university", Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The aim of the work is to analyze the possibility of using local networks with synchronous access time in the computer rooms of the university. Issues related to the efficiency of local networks are considered based on an analysis of its time characteristics, such as the standard deviation and dispersion of the delay line in continuous time, as well as the average delay time of the data packet, taking into account the requirements for modern local networks. The corresponding simulation was performed and the results obtained.

Keywords: local network, time characteristics, computer audience, modeling, synchronous access, access time, computer simulation.

---

OPTION OF HARDWARE SUPPORT OF PLANNING ALGORITHMS AND DISPATCHING TASKS OF A MULTIPLE PROCESSOR RECONFIGURABLE COMPUTING SYSTEM

 

A.I. Martyshkin

Ph.D., Associate Professor, Associate Professor of the Department of Computers and Systems, FGBOU VO ‘Penza State Technological University’, Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The paper presents one of the possible options for hardware support of algorithms for the subsystem of scheduling and scheduling tasks in a multiprocessor reconfigurable system. In the course of the study, it was found that the use of hardware support for scheduling and dispatching algorithms makes it possible to much faster determine which task from the ready-to-run queue should receive the next processor time than the software implementation of the same algorithms inside the operating system scheduler.

Keywords: hardware support, reconfigurable computing system, processor, task manager, scheduler, operating system.

---

HARDWARE SUPPORT AND VERIFICATION OF THE OPERATION OF THE TASKMAN CONTROLLER OF A MULTI-PROCESSOR RECONFIGURABLE COMPUTING SYSTEM

 

A.I. Martyshkin

Ph.D., Associate Professor, Associate Professor of the Department of Computers and Systems, FGBOU VO ‘Penza State Technological University’, Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The article presents the possibility of hardware implementation and verification of the correctness of the work of the task manager of a multiprocessor reconfigurable computing system. The verification method in the SMV program is given. In the course of the study, a non-deterministic NDA automaton encoding was obtained in the input language SMV in accordance with the described method.

Keywords: reconfigurable computing system, task manager, algorithm verification, process synchronization, operating system, SMV program.

---

POSSIBLE ARCHITECTURE OF THE STORAGE SYSTEM OF DATA OF THE ACHIEVEMENTS OF THE STUDENT OF THE UNIVERSITY BASED ON BLOCKCHAIN TECHNOLOGY

 

A.I. Martyshkin

Ph.D., Associate Professor, Associate Professor of the Department of Computers and Systems, FGBOU VO ‘Penza State Technological University’, Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The article presents the result of a study of the applicability of the Blockchain technology for the implementation of distributed registries of personal data, based on the example of the university student achievement register. The organization of interaction in the system is considered. An expression is provided to calculate the transaction hash.

Keywords: distributed systems, blockchain, cryptocurrency, information technology, registry, token, hash identifier.

---

OVERVIEW OF USER PERSONAL MANAGEMENT PROGRAMS

 

A.I. Martyshkin

Ph.D., Associate Professor, Associate Professor of the Department of Computers and Systems, FGBOU VO ‘Penza State Technological University’, Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The article discusses some of the existing programs for managing the user's personal schedule. Well-known existing programs are given and analyzed, in which advantages and disadvantages are highlighted. In conclusion, it was concluded that all the programs presented in the work have excessive functionality, therefore it is advisable to develop a simple and functional organizer.

Keywords: planning, personal schedule, organizer, program, alert, reminder.

---

OPPORTUNITIES BLOCKCHAIN TECHNOLOGY IN THE APPLICATION FOR CREATING DISTRIBUTED DATA REGISTRIES

 

A.I. Martyshkin

Ph.D. Associate Professor, Associate Professor of the Department of Computers and Systems, FGBOU VO ‘Penza State Technological University’, Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The article presents the result of a study of the applicability of the Blockchain technology for the implementation of distributed registries of personal data, based on the example of the university student achievement register. The organization of interaction in the system is considered. An expression is provided to calculate the transaction hash.

Keywords: distributed systems, blockchain, cryptocurrency, information technology, registry, token, hash identifier.

---

---

MINING OBJECTS: CONCEPT OF MULTILEVEL MONITORING OF THEIR GEOHYDROMECHANICAL STATE

 

Anatoly Kalashnik

Leading Researcher of Geoflyuidomechanikal Laboratory, Dr (Eng.), Mining institute KSC RAS, Apatity, Russia, e-mail:This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. Conceptual approaches to forming of multilevel monitoring of a geohydromechanical status of mining objects which basis the principle of integration of the cross-disciplinary researches including land and GPS geodetic, geophysical and hydrological measurements and also subsurface, land, air and satellite georadar shooting is are stated. Approaches are based on carrying out regime observations at the different levels: remote, air, land, subsurface and also computer simulation, and synchronous processing of results with use of information technologies «BIG DATA» and «CLOUD SERVICE». Natural multilevel researches make a basis of monitoring as a result of which data retrieved about a geohydromechanical status of mining objects in the automated mode supplement databases of decision making support system. Multilevel approach is used also in computer simulation: 2D and 3D models of mining objects as hierarchically enclosed structures are created, with their multilarge-scale research. The concept of multilevel complex monitoring of a geohydromechanical status of mining objects is approved at the main mining enterprises of the Kola Peninsula.

Keywords: mining objects, monitoring, multilevel researches, integration, industrial and environmental safety.

---

RESEARCH OF COMFORT OF TRANSPORTATION OF PEOPLE TO THE PLACE OF WORK BY THE SPECIAL BUSSES

 

Olga Khodos ¹

¹ senior teacher of Department of Automobiles and Automobile Economy, National Technical University ‘Dnipro Polytechnic‘, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. Conducted theoretical research of comfort of transportation of people to the place of work by the special busses.

Keywords: special bus, comfort.

---

QUESTIONS OF DEVELOPMENT OF MONITORING SYSTEM AND CONTROL OF EMERGENCY SITUATIONSA.

 

U. Analiyeva

teacher of Scientific and educational complex KazNIITU Uralsk, Kazakhstan, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The article is devoted to the development of the concept of building an automated system for monitoring and controlling emergencies and determining its structure and location. Examples of monitoring objects are given and the relevance of the development and implementation of such systems is shown. The proposed concept implies a multi-level hierarchical structure of the monitoring system with an open architecture, at the lower level of which are multifunctional sensors of physical quantities installed on controlled objects or territories. It is proved that, to a greater extent, it is the sensors that determine the reliability and information content of the entire monitoring system. With reference to the mudflow hazard monitoring system, the range of sensors used has been determined. The issues of raising awareness and efficiency of monitoring and warning are considered. It is shown that the proposed concept can be implemented and function properly only with the availability of modern software and hardware. Using the example of a 4-tier monitoring system, the tasks solved at its various levels are described in detail.

Keywords: environment, monitoring, control, sensors, disaster, man-made, mudflow, pollution, interface.

Topic 9 - Information Technology in Education

---

CONDUCT OF PATENT STUDIES IN THE PREPARATION OF ENGINEERING STAFF FOR THE MINING AND METALLURGICAL INDUSTRY

 

Yaroslava Gerasimenko¹, Tatyana Gerasimenko², Evgeny Meshkov³

¹student of the North Caucasus Mining and Metallurgical Institute (State Technological University), Vladikavkaz, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

²Ph.D., Associate Professor of the Department "Technological Machines and Equipment" of the North Caucasus Mining and Metallurgical Institute (State Technological University), Vladikavkaz, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

³Ph.D., Dr., Professor of the Department of Metallurgy of non-ferrous metals and automation of metallurgical processes of the North Caucasus Mining and Metallurgical Institute (State Technological University), Vladikavkaz, Russia,

e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The paper describes the importance of training engineers for the mining and metallurgical industry in the field of intellectual property. It is established that patent research broadens the specialist’s outlook, contributes to the development of his creative and inventive skills. These skills allow you to provide a high scientific level of their own development. It has been found that conducting patent research activates technical creativity and increases the inventive activity of specialists.

Keywords: patent research, engineering creativity, patent information, intellectual property.

---

MODEL OF ENERGY CONSUMPTION THROUGH TORNQUIST FUNCTIONS

 

Olena Korniichuk

Ph.D., Associate Professor, Zhytomyr Agro-technical College, Zhytomyr National Agroecological University, Zhytomyr, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The construction and analysis of the energy demand model depending on the income level of household consumers. The model is built using Tornquist lines, based on the concept of monotony of functions, on the theory of consumption, supply and demand, using computer graphic interpretation of the research.

Key words: demand, income, consumption, energy supply, household, Tornquist demand functions.

---

A FORMALIZED METHOD FOR OBTAINING QUANTITATIVE ESTIMATES OF META-COMPETENCES ARE INFLUENCED LEARNER BASED ON HIS BEHAVIOR IN SOCIAL NETWORKS

 

E.G. Bershadskaya

Ph.D., Professor of the Department of Computers and Systems, FGBOU VO ‘Penza State Technological University’, Penza, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The article is devoted to analysis of computer networks, a formal definition of quantitative characteristics, which can be useful for the analysis of information obtained from social networks. The software implementation proposed by the authors, allows to extract information from social networks, to processing, analysis and visualization of data.

Keywords: social networks, data analysis, meta-competences.

---

SOFTWARE-HARDWARE TRAINING COMPLEX

 

A.P. Mikhailov

leading specialist, OOO PLK Sistemy Moscow, Russian Federation This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract Progress of Informatization and introduction of the latest programs and information technologies is now an indispensable attribute of the developed society. In the industry, the latest equipment and control systems for various technological processes and facilities are necessarily equipped with computer control and monitoring systems. Therefore, the constant improvement of their knowledge in the field of information technology is a prerequisite for a modern specialist, especially in the field of industrial technology.

Keywords: information, object, hydraulics, APCS, model, system, program, simulator.

Topic 10 – Humanities Education Issues