slide01644662E6-1AFE-52A3-F691-CA8C5E4359F0.jpg
slide02D3D0292E-B595-E697-0D9B-E91BFB001D0A.jpg
List of accepted scientific papers to be published in conference proceedings.


ISSN 2312-198X (Online), ISSN 2311-147X (CD-ROM) Contemporary Innovation Technique of the Engineering Personnel Training for the Mining and Transport Industry 2021 (CITEPTMTI’2021). Conference Proceedings.


Conference dates:
23-24 April 2021.

Dnipro University of Technology


Dnipro

Ukraine
Scientific Conference 2021 
List of accepted scientific papers to be published in conference proceedings.
ISSN 2311-147X Contemporary Innovation Technique of the Engineering Personnel Training for the Mining and Transport Industry 2021 (CITEPTMTI’2021). Conference Proceedings.

Conference dates:
23-24 April 2021.
Dnipro University of Technology

Dnipro City
Ukraine
CITEPTMTI2019u.jpg


Topic 1 - Mining and Metallurgical Equipment



ABOUT APPLICATION OF HIGH-CLASS MECHANISMS OF CRUSHING MACHINES

 

Serhii Shatov1 Irina Matsyuk2, Eduard Shlyakhov3

1Ph.D., Dr., professor, Department Construction and Road-Building Machines, State Higher Education Establishment “Prydniprovs’ka State Academy of Civil Engineering and Architecture”, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Associate Professor of the Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

3Associate Professor, Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The paper considers the results of a study of the use of high-class mechanisms in heavy-duty crushing machines.

 

Key words: crushing, jaw crusher, lever mechanism, gripping angle, Mathcad, complex movement of cheeks.


METHODS OF DETERMINING THE TIME OF THE MATERIAL CONTACT WITH THE WORKING SURFACE IN THE VIBRATING JAW CRUSHER WITH AN INCLINED CRUSHING CHAMBER

 

O.V. Fedoskina

Ph.D., Associate Professor of the Department of Engineering, Technical Aesthetics and Design, Dnipro University of Technology, Dnipro, Ukraine, e‐mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The paper analyzes the experimental methods for determining the contact time of the working surface of the cheek with the material in a single impact.

 

Key words: crusher, crushing chamber, oscillogram, method, sensor, elastic elements.



Topic 2 - Mechanical Engineering and Engineering Science



POWDER ANTIFRICATION MATERIALS

 

V.E. Olishevska1, H.S. Olishevskiy2

1Ph.D., Associate Professor of Automobiles and Automobile Economy Department, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Associate Professor of Power Engineering Department, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The chemical composition, microstructure, physical-mechanical and tribological properties of powder antifriction materials: iron - graphite, iron - copper, iron - copper - graphite, iron - copper - graphite - phosphorus, bronze-based compositions, iron - graphite – molybdenum, are described in the article. Features of friction of powder antifriction materials are considered. Marking and rational areas of use of powder antifriction materials are given. The article content facilitates the perception of the material, reduces the time for acquaintance and increases the integral competence of students in the conditions of distance scientific and educational process.

 

Keywords: powder antifriction materials, physical and mechanical properties, tribological properties, operational properties, friction coefficient.


ABOUT COMPUTER PROGRAMS FOR SIMPLIFIED STRENGTH AND STIFFNESS ANALYSIS OF I-BEAMS.

 

Yuri Kholodniak1, Kostikov Alexander2, Kaporovych Svitlana3

1Ph.D., Associate Professor, Head of Technical Mechanics Department, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Associate Professor of Manufacturing Processes and Automation Engineering Department, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

3Ph.D., Senior Lecturer of Technical Mechanics Department, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

1,2,3 Donbass State Engineering Academy, Kramatorsk, Ukraine

 

Abstract. An additional calculation unit has been developed for previously created computer programs for simplified calculation of the strength of statically determined I-beams. Advanced programs determine the support reactions of beams, plot transverse forces and bending moments, select the necessary I-beam numbers, as well as determine the desired displacements and plot their changes along the length of the beams. The introduction of these programs into the educational process will provide students with new opportunities to develop their professional skills. The developed programs will also be useful for practitioners in solving real technical problems.

 

Keywords: I-beams, strength, displacement, simplified calculations, Mathcad, computer programs.


ANALYSIS OF THE EFFICIENCY OF COMPREHENSIVE RESOURCE SAVING TECHNOLOGY FOR IMPROVING THE QUALITY OF SECONDARY FOUNDRY ALUMINUM ALLOYS WITH HIGH IRON CONTENT

Yuri Dotsenko1, Vadim Seliverstov2

1Ph.D., Associate Professor of Design, Technical Aesthetics and Design. National Technical University "Dnipro Polytechnic", Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., professor of the department of foundry production. National Metallurgical Academy of Ukraine, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.com

 

Abstract. The paper analyzes the influence of complex technology on the properties of cylindrical castings from cast aluminum alloy AK7 with high iron content. The results of researches of mechanical properties are resulted.

 

Keywords: aluminum alloy, casting, modification, mechanical properties, crystallization.


SELECTION AND CALCULATION OF THE REPLACEABLE MILLING HEAD MAIN PARAMETERS FOR THE SINGLE-BUCKED EXCAVATOR

Maksym Balaka1, Dmytro Palamarchuk2, Anna Kim3

1Ph.D., Associate Professor of Building Machines, Department, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Associate Professor of Professional Education, Department, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

3Student of ILS-51 group, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

1,2,3Kyiv National University of Construction and Architecture, Kyiv, Ukraine

 

Abstract. The selection and calculation of the designed milling head main parameters, which is used as a replaceable operating element for the single-bucked excavator, are considered in this paper. The milling head is driven by a built-in gear motor that combines all the advantages of planetary gears. The constructive and operational mass of the excavator with a replaceable milling head is determined.

 

Keywords: milling head, parameter, planetary gear, excavator.


RESOURCE-SAVING TECHNOLOGIES OF MODIFICATION AND THE EFFECT OF PRESSURE DURING SOLIDIFICATION ON THE PROPERTIES OF CASTINGS FROM A CAST ALLOY SYSTEMS Al-SI

 

Yuri Dotsenko1, Vadim Seliverstov2

1Ph.D., Associate Professor of Design, Technical Aesthetics and Design. Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Dr., professor of the department of foundry production. National Metallurgical Academy of Ukraine, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The analysis of the current modifiers, which are used for processing of alloys of the system Al-Si and methods of influence on the crystallizing melt. Shown their advantages and disadvantages. Results of research of influence of an alternating gas-dynamic pressure and modifying the structure of metal castings of alloy A356.

 

Key words: modification, gas-dynamic effects, foundry alloy, casting, technology, and mechanical properties.


ADAPTIVE EQUIPMENT FOR OPENING OF UNDERGROUND PIPELINES

 

Sergiy Lysak1, Vladislav Repin2

1Master, teacher of special disciplines, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Master, teacher of special disciplines, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

1,2 Mykolayiv building college KNUCA, Mykolayiv, Ukraine

 

Abstract. The relevance and technical aspects of the development of adaptive working equipment of the machine for opening underground pipelines used during their overhaul are considered in the work. Approaches to the mathematical calculation of the optimal basic parameters of the machine are given.

 

Keywords: repair, pipeline, trench, ground, bucket.


INCREASING THE DENSITY OF BEARING ASSEMBLIES IN BELT FILTER PRESSES

 

Yegor Bolohin1, Irina Matsyuk2

1student, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Associate Professor of the Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. In the work, the analysis of the operation of the belt filter press at high motor speed and the operating conditions of the bearings is carried out. The reasons for the rapid wear of bearings and the installation of a sleeve or bearings with an external seal as a solution to the problem are considered.

 

Keywords: filter press, bearing, external seal.


BASIC MATERIALS CHARACTERISTICS ANALYSIS FOR 3D PROTOTYPING FOR EDUCATIONAL PURPOSES

 

Vladislav Vyshnevetskyi 1, Irina Matsyuk2, Оleksander Tverdokhlib 3

1Student, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Associate Professor of the Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

3Senior lecturer of the Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. Theoretical researches of materials for 3D printing and prototyping for studying of additive technologies of production are carried out in the work.

 

Keywords: additive technologies, prototyping, 3D printing, 3D printer, materials for 3D printing, ABS plastic, PLA plastic.


RESEARCH OF PARAMETERS OF SURFACE HARDNESS AND THERMAL SHRINKAGE OF PRODUCTS FROM PLA AT THEIR MANUFACTURING BY A METHOD OF 3D PRINTING

 

Nataliia Rott1, Viktoriia Dytiuk2, Oleksii Myrnyi3

1 Ph.D., associated professor, Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, , E-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Assistant, Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, E-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

3Student of group 132-20sk-2, Dnipro University of Technology, Dnipro, Ukraine

 

Abstract. This article of surface hardness of the material and the effect of printing temperature on the heat shrinkage of PLA-plastic products in the temperature range 190 - 220°C.

 

Keywords: 3D printing, PLA plastic, heat shrinkage, surface hardness.



Topic 3 - Transport Technologies and Equipment



ABOUT THE SIZE OF THE GROUNDING DEVICE ON THE BOAT

 

Mikhail Pustovetov

Ph.D., Engineer of Engineering Technology Department,

Technological Institute (Branch) of Don State Technical University, Azov, Russia, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. Regulatory documents that should guide engineering and technical workers in the implementation of a technical solution contain directives, instructions or recommendations without a detailed explanation of the reasons and mechanisms for their formation. Nevertheless, the content of the normative documents has a technical, physical basis. The author offers explanations for the choice of the size of the grounding device on the boat, based on the calculation of the current spreading resistance of the sheet grounding conductor.

 

Keywords: small vessel, current-insulating hull, earthing device, system with insulated neutral.


VEHICLES WITH AN ALTERNATIVE FUEL FORECAST AND IT DEVELOPMENT

 

V.V. Krivda

Ph.D., Associate Professor of the Department of Automotive and Automotive Industry, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The paper provides an analysis of vehicles using alternative fuels, including vehicles operating in a complex on several types of fuel, hybrids, electric vehicles, cars on hydrogen fuel.

 

 

Keywords: car, vehicle, hybrid, alternative energy, fuel.


TESTING THE BRAKE SYSTEM OF THE HYBRIDIZED VEHICLE ZAZ SENS

 

V.O. Fedoskin1, K.I. Kornilenko2, M.M. Yerisov3

1Ph.D., Associate Professor of the Department of Automobiles and Automobile Economy, Dnipro

University of Technology, Dnipro, Ukraine, e‐mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Assistant, Department of Automobiles and Automobile Economy, Dnipro University of Technology, Dnepr, Ukraine, e‐mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

3Assistant, Department of Automobiles and Automobile Economy, Dnipro University of Technology, Dnepr, Ukraine, e‐mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The paper presents the results of experimental studies of the SENS vehicle brake system with a modernized rear beam and motor wheels installed on it. It is shown that with the developed constructive solution, the braking distance is within the permissible value.

 

Keywords: car, braking distance, motor-wheel, hybrid, rear beam, travel speed.


GENERAL METHODS AND MODELS OF EV CHARGING STATIONS OPTIMAL LOCATIONS

 

A. Maliienko1, I. Lutsenko2, S. Fedoriachenko3

1Ph.D., Associate Professor of the Department of System Analysis and Control, Dnipro University of Technology, Dnipro, Ukraine e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Professor of the Power Engineering Department, Dnipro University of Technology, Dnipro, Ukraine e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2 Ph.D., Department of Generative Design, Dnipro University of Technology, Dnipro, Ukraine e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. This paper presents the main methods of multiple set coverage for modeling and solving problems of optimal placement of charging stations of electric vehicles.

 

Keywords: charging station, mathematical model, optimization methods.


INCREASE OF POPULATION TRANSPORT SERVICE ACCORDING TO EFFECTIVE SYSTEM FORMATION OF URBAN PASSENGER GROUND ELECTRIC TRANSPORT

 

Serhiy Cheberyachko1, Olena Tretyak2, Viktoriya Dotsenko3

1Ph.D., Dr., Professor of Department of Labour Protection and Civil Safety, Dnipro University of Technology, Dnipro, Ukraine; e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Associate professor of Department of Transportation Management, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

3Student of group 275-19 ck-1, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The paper investigates measures aimed at improving the transport service of the city population by introducing into the system of urban land electric transport an effective vehicle - a modern tram based on integrated assessment of consumer, technical and economic, technical and operational, ergonomic and others. properties in the formation of a rational structure or modernization of the existing fleet of vehicles operated in large cities.

 

Keywords: tram, urban ground passenger transportation by electric transport, technical and operational properties, technical and economic properties, comfort, safety.



Topic 7 - Informational Technologies of Design, Modeling, Design, Modern WEB-technologies



TECHNICAL CHARACTERISTICS OF PHOTOPOLYMER MATERIALS STUDY AND IT APPLICATION AT 3D PROTOTYPING TECHNOLOGIES COURSE

 

Anna Fartushna1, Irina Matsyuk2, Оleksander Tverdokhlib3

1Student, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Associate Professor of the Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

3Senior lecturer of the Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. Theoretical researches of photopolymer materials for 3D printing, technical characteristics and application of products in life are carried out in the work.

 

Keywords: prototyping, photopolymer materials, 3D printing, stereolithography, digital projector LED projection, 3D printing technology SLA.


CLOUD SERVICES IN INDUSTRIAL DESIGN

 

Ilya Verner1, Viktoriia Dytiuk2, July Salomatina3

1,2Assistant, Department of Engineering and Generative Design, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

3Student, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

1,2,3Dnipro University of Technology, Dnipro, Ukraine

 

Abstract. This article considers review of cloud technologies ways usage in industrial design. The results of the introduction of these technologies are presented on the example of training specialists of the mechanical and mechanical engineering faculty of the university. An overview of current graphic services has been performed, which expands the capabilities of information visualization.

 

Keywords: education, visualizer, cloud technologies, graphic services, design.



Topic 8 - Applied Geometry, Engineering Graphics, Ergonomics, Life Safety



USE OF SPECIALIZED 3D-MODELING PROGRAMS IN ORDER TO IMPROVE THE QUALITY OF MASTERING OF GRAPHIC DISCIPLINES

 

Tamara Savelieva1, Dmytro Pustovoi2

1Ph.D., Associate Professor of Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2Ph.D., Associate Professor of Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. Possibilities and prospects of training students of engineering and technical specialties using the modern computer technology are considered. It is shown that the training of specialists who are able to use CAD tools and solve specific problems of modern production, allows to intensify the educational process and increase the competitiveness of future professionals in the labor market.

 

Keywords: graphic disciplines, CAD, design activities, 3D modeling.


APPLICATION OF VIDEO LESSONS IN TEACHING GRAPHIC DISCIPLINES TO THE STUDENTS OF ENGINEERING AND TECHNICAL SPECIALTIES

 

Dmytro Pustovoi1, Oleksii Myrnyi2

1Ph.D., Associate Professor of Department of Engineering and Generative Design, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

2student, Dnipro University of Technology, Dnipro, Ukraine, e-mail: This email address is being protected from spambots. You need JavaScript enabled to view it.

 

Abstract. The article emphasizes the relevance of the introduction and discusses the advantages of teaching of the graphic disciplines using targeted video tutorials during the studying of the discipline "Engineering and computer graphics". The introduction of certain changes in the educational process of studying graphic disciplines is substantiated, taking into consideration the growing role of information and multimedia technologies in the educational process.

 

Keywords: videolesson, graphic disciplines, information and educational technologies, AutoCAD.